![]() The biggest upgrade on the Wavlink dock compared to the Plugable one is the ability to connect two 4K displays. The dock also has a lot more ports which give you better connectivity options. Ports: 6 x USB 3.0, 2 x HDMI, 2 x DP (dual video outputs), 1 x USB-C (In), 1 x Gigabit Ethernet, 1 x Audio out, 1 x Micįor a few bucks more, the Wavlink docking station allows you to connect higher resolutions displays to your Mac.The reviews say the Plugable dock is reliable and it can help boost your productivity. What’s more, while you can use a monitor with a high refresh rate, the dock will limit the refresh rate to 60Hz, which is a bit of a bummer. Note that the max supported resolution of each monitor is 1920×1200. You can connect up to two monitors to your MacBook Air or Pro using the two HDMI ports on the Plugable dock. The rear houses four more USB-A ports albeit with 2.0 speeds. The dock comes with two USB-A 3.0 ports on the front for easy access. So it’s important to note that it’s meant to be used on your desk and it isn’t geared for travel. The Plugable USB-C Laptop dock is a full-fledged docking station. You also get additional ports like USB-A and an Ethernet connector with the device. There are two HDMI ports that can output at 1080p 60Hz. Plugable’s DisplayLink dock is one of the most affordable adapters you can buy to connect multiple monitors to your Mac. Ports: 2 x HDMI, 2 x USB 3.0, 4 x USB 2.0, 1 x Gigabit Ethernet, 1 x 3.5mm Audio.So, expand your horizon by choosing the best DisplayLink docking stations for Mac M1 from the list that follows. Some docks on this list even allow you to connect up to three external monitors with your M1 MacBook Air or Pro. The dock is then connected to the Mac via a USB-C port. To do so, you must connect external monitors to the DisplayLink dock. However, due to the limitations of the M1 chip, you cannot connect more than one external monitor via any of the conventional ports.Ī DisplayLink dock solves this issue by letting you connect external monitors via USB ports. Generally, monitors connect to your computer via HDMI, DisplayPort, or Thunderbolt. In simple terms, DisplayLink is a chip that allows you to interface monitors via USB. Charge your MacBook on the go using a power bank with USB-C Power Delivery.Want a new charger for your Mac? We have a list of 100W USB-C chargers to charge your MacBook.You might want to take a look at some budget monitors for a dual-monitor setup if you don’t want to spend too much.If you want to use a dual or triple monitor setup with your M1 Mac, here are some DisplayLink-compatible docks to buy.īefore that, here are some other articles that may interest you – All you have to do is connect the dock to your Mac and plug all your monitors into it. Thankfully, there’s a simple workaround and you can connect multiple monitors via DisplayLink docks.Ī DisplayLink adapter allows you to connect multiple monitors to your M1 Mac. To wit, you cannot connect more than one external display to your M1 Mac. Be that as it may, M1 Macs have a glaring drawback that bothers several users. And, despite being a couple of years old, the M1 MacBook Air and MacBook Pro are fantastic laptops that offer great performance and endurance. DisplayLink nf -įile: /etc/X11//nfĬat: /etc/X11//20-displaylink.Apple took the computer market by storm with its custom M1 chipset. VGA (3D): NVIDIA Corporation Device 25a5 (rev a1) VGA: Intel Corporation Device 9a60 (rev 01) DisplayLink info -ĮVDI service version: /sys/devices/evdi/version not found ĭid you read Post Installation Guide? yĭid you read Troubleshooting most common issues? y displaylink-debian.sh -debug Starting Debug. I'm really stuck on this and would like to use another external monitor through my USB portsĪdditional output from running. Make -j16 KERNELRELEASE=5.13.0-43-generic all INCLUDEDIR=/lib/modules/5.13.0-43-generic/build/include KVERSION=5.13.0-43-generic DKMS_BUILD=1.(bad exit status: 2)ĮRROR (dkms apport): binary package for evdi: 1.10.1 not foundĮrror! Bad return status for module build on kernel: 5.13.0-43-generic (x86_64)Ĭonsult /var/lib/dkms/evdi/1.10.1/build/make.log for more information.ĮRROR: Failed to install evdi to the kernel tree. Kernel preparation unnecessary for this kernel. Patch unexpectedly ends in middle of lineĭistribution discovered: Ubuntu 20.04.4 LTSĬreating symlink /var/lib/dkms/evdi/1.10.1/source -> Patching file 5.5/displaylink-driver-5.5/displaylink-installer.sh Uncompressing DisplayLink Linux Driver 5.5.0-59.151 100% Inflating: 5.5/displaylink-driver-5.5.Ĭreating directory displaylink-driver-5.5.0-59.151 Inflating: 5.5/DisplayLink USB Graphics Software for Ubuntu 5.5.0-59.151-Release Notes.txt Here is additional logging output: Preparing for install I'm specifically failing when the evdi package has to be built on the kernel I am having an issue installing the drivers for the Community DisplayLink
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |